Odl Tubular Skylight Manual de usuario

TUBULARSKYLIGHTInstallation Instructions ImportantBe sure to first read through and then follow completely all step-by-step instructions. This will he

10LadderPhillips ScrewdriverSafety Equipment3/4” Dome ScrewsDome WashersTop Adjustable TubeSolar DomeExterior Clear Pure SiliconeTOOLS & PARTSFor

1011PencilPhillips ScrewdriverPower SawHole Cutting TemplateCeiling Trim RingTOOLS & PARTS Use a keyhole/drywall saw to cut the hole.2Using the co

12Measuring TapeBottom Adjustable TubeFoil TapeTOOLS & PARTS1If you have an angled installation you will need to twist your Bottom Adjustable Tube

131Carpenter PencilMetal ShearsSafety EquipmentSafety GlassesExtension TubesGlovesTOOLS & PARTSBe sure to measure and cut if necessary, before rem

14More Than 48”26” Through 48”Less Than 25”Tube Extension (Sold separately )(Must use bottom adjustable tube only )Section-8Tube Length Chart

1415TOOLS & PARTSInstallation Complete!Install the Diffuser Assembly by aligning the Diffuser with the three tabs on the Trim Ring. Turn clockwise

16LadderPencil/MarkerSafety EquipmentShimBottom Adjustable TubeTOOLS & PARTSPlace bottom adjustable tube (blue label) (with the flanged end down) t

17GlovesladderMetal ShearsSafety EquipmentBottom Adjustable TubeCeiling RingTOOLS & PARTSAt the ceiling, slide the temporary shim out of your way

18LadderPhillips ScrewdriverSafety Equipment3/4 Dome ScrewsDome WashersBottom Adjustable TubeDiffuserSolar Lens DomeTOOLS & PARTSInstallation Comp

19(2) 2-1/2” Pan Head Sheet Metal Screws (Not Included)3/32” BitDrillPhillips Drill BitTOOLS & PARTSOn roof, locate and install Top Adjustable Tub

23For cathedral ceiling, see Section 10.For long tube shaft installation, see Section 11.For metal roof installations, see Section 12.For tile roof in

2021DrillDrill Bit (For Metal)GlovesHole Cutting TemplatePower SawTOOLS & PARTSAfter finding your roof location, drill up through the roof until it

21Caulk GunMeasuring TapeMetal ShearsRoofing SealantSafety EquipmentPlastic Underlayment FlashingTOOLS & PARTSDraw a horizontal line across the cen

2223DrillPhillips ScrewdriverGlovesRoofing SealantHole Cutting TemplateFormable Main Flashing(9) 2” Screws(9) 3/4 WashersTOOLS & PARTSSlide the UPP

2223DrillDrill BitFormable Aluminum FlashingPencilSpike/RodTOOLS & PARTSAfter finding your roof location, drill up through the roof. Then drive a

2425TOOLS & PARTSCarefully remove the tiles or shingles from the “work area”. Set them aside in the same order or pattern as when attached to the

2425Metal ShearsSafety EquipmentClear Plastic UnderlaymentTOOLS & PARTSCut a slit through the felt paper at the “3:00 and 9:00” positions. Be sur

2627TOOLS & PARTSDo a practice run of installing the Clear Plastic Underlayment, Formable Aluminum Flashing, and the reflective tubeRemember to use

2627Caulk GunRoofing SealantSafety EquipmentClear Plastic UnderlaymentTOOLS & PARTS1SealantSecure the Clear Plastic Underlayment to the roof deck b

2829TOOLS & PARTSGlovesFormable Aluminum FlashingClear Plastic UnderlaymentTop Adjustable Tube 213Clear Plastic UnderlaymentFormable AluminumFlash

2829Sealant1TOOLS & PARTSOnce the Formable Aluminum Flashing is shaped to match the downhill tiles, clean and dry the surfaces of aluminum, felt

23Limited Warranty for ODL Tubular SkylightsEffective 02/04Warranty CoverageSubject to the conditions, exclusions and limitations herein, ODL Incorpo

3031TOOLS & PARTSGlovesSafety EquipmentExterior ClearPure SiliconeReinstall the trimmed tiles at the sides of the roof cutout, making sure to inst

3031123For new homes and projects requiring building permits cut out NFRC label once product installation is complete.Affix to diffuser ring as shown a

45Solar Lens® Dome(10” Dome shown)Adjustable TubesRoof Flashing(Composite flashing shown)Ceiling Ring with Flip TabsPARTSLow-Profile InsulatedDiffuser L

45In the attic, locate the coat hanger wire. Adjust its location, centering the opening for the tube between the framing members. Check wire visibili

67Angled Tube InstallationIn the attic, if there are obstructions at the roof location (valleys, wires, pipes, ducts, framing, etc.), adjust tubes up

671Adjustable TubesHole Cutting TemplateTOOLS & PARTSRemove protective film from inside all tubes.111It is recommended that you put all of your too

89Select the correct hole cutting template for the tube (10” or 14”).1Locate the protruding nail. Use the correct hole-cutting template to trace the d

89The vertical seam of the reflective tube should point to the East or West to avoid irregular light patterns in your room.TIPUse a flat pry bar to care